Cambium Networks 10Gbps SFP+ MMF Optical Transceiver, 850nm, 300m

Cambium Networks 10Gbps SFP+ MMF Optical Transceiver, 850nm, 300m

MPN SFP-10G-SR

Item no. W125970371

EAN/UPC 5704174389774

Stock level

The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.

The transmitter converts 10Gbit/s ...

Read full description
    Exact alternatives
    Lanview SFP+ 10 Gbps, MMF, 300 m, LC, DDMI support, Compatible with Cambium SFP-10G-SR
    Lanview SFP+ 10 Gbps, MMF, 300 m, LC, DDMI support, Compatible with Cambium SFP-10G-SR
    Designed for Network
    MPN
    Item no.
    MO-CM-SFP-10G-SR
    W128227484

    Specifications for SFP-10G-SR

    Features

    Hot-Plug support

    Yes

    Package dimensions

    Gross Weight (Package, kg)

    0.04 kg

    Performance

    Interface type

    SFP+

    Maximum data transfer rate

    10000 Mbit/s

    Maximum transfer distance

    300 m

    Multi-mode fiber (MMF) supported

    Yes

    Networking standards

    IEEE 802.3ae

    SFP transceiver type

    Fiber optic

    Wavelength

    850 nm

    Product dimensions

    Net Weight (Product, kg)

    0.006 kg

    Vendor information

    Warranty

    1 Year(s)

    Description

    10Gbps SFP+ MMF Optical Transceiver, 850nm, 300m

    The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.

    The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor

    The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.

    *The product data above is provided by Icecat. EET cannot be held responsible for errors in relation to this.

    EET InternationalBregnerødvej 133 D3460 BirkerødVAT no. 35239480
    International / English